Posted  by 

Drivers Epson Dfx 8500 Tractor

You are providing your consent to Epson America, Inc., doing business as Epson, so that we may send you promotional emails. You may withdraw your consent or view our privacy policy at any time. To contact Epson America, you may write to 3840 Kilroy Airport Way, Long Beach, CA 90806 or call 1-800-463-7766.

Drivers Epson Dfx 8500 Tractor

Last Updated on Mon, 20 Nov 2017 When you install the ribbon feed change lever unit, join the tip of the tractor select lever and the tractor select gear holder correctly. (Refer to Figure 2-12.) 3.2.6.3 Tractor Select Lever (Upper and Lower) Assembly Disassembly This section describes how to disassemble the tractor select lever assembly, including how to remove the ribbon feed motor and tractor select sensor. Step 1: Remove the ribbon feed change lever unit. (Refer to Section 3.2.6.2.) Step 2: Remove the two CP(S-P1)(M3x6) screws, leaf springs, and washers securing the ribbon feed motor to the ribbon feed motor frame and remove the motor. Step 3: Remove the E ring (# 3) securing the upper/lower tractor select levers and remove the levers. Step 4: Remove the E ring (# 3) securing the tractor select cam and remove the cam. Step 5: Remove the CPS(P1)(M2x10) screw securing the tractor select sensor and remove the sensor.

Step 6: Using wire cutters, cut the wire band securing the ribbon feed motor and tractor select sensor cables to the ribbon feed motor frame. Dunia Download Game Hp Gratis Gameloft Terbaru 2017. Tractor Select Lever Disassembly z Attach the tractor select levers to the tractor select cam as shown in Figure 3-50.

(Upper and Lower) Figure 3-50. Tractor Select Lever Installation 3.2.6.4 Ribbon Jam Sensor Removal Step 1: Remove the right cover.

(Refer to Section 3.2.3.2) Step 2: Disconnect the connector for the sensor from the connector junction board. Step 3: Remove the CP(S-P1) (M3x6) screw securing the sensor to the bracket, and remove the sensor. Ribbon Jam Sensor Removal 3.2.6.5 Connector Junction and FPC Board Assembly Removal This section describes how to remove the connector junction board assembly and FPC board assembly. Step 1: Remove the left side cover. (Refer to Section 3.2.3.2) Step 2: Disconnect all the cables from the connector junction board assembly. Remove the two CP (S-P1) (M3x6) screws securing the connector junction board assembly to the and then remove the connector junction board assembly.

Step 3: Remove the front/rear tractor select lever assembly. (Refer to Section 3. Telecharger Driver Hp 3500 Mt La. 2.6.2) Step 4: Disconnect the connector for the CR sensor (encoder) from the FPC board assembly. Step 5: Remove the 2 CBS (M3x8) screws securing the FPC cover and remove the cover (Refer to Figure 3-10). Then remove the CPS(P-1) (M3x6) screw securing the FPC board assembly to the printer mechanism and remove the FPC board assembly. Connector Junction Board Removal ASSEMBLING POINT When you connect the cables to the connector junction board assembly, note that the matching connectors have the same color and number of pins (Refer to APPENDIX Figure A-15.). 3.2.6.6 PG Sensor and Removal ^CAUTION When you remove or install the PG sensor, be careful not to bend the PG motor. Step 1: Remove the connector junction board assembly.

(Refer to Section 3.2.6.5) Step 2: Remove the CBS screw (3X6) securing the PG sensor unit to the left frame. Then take out the unit to the front and remove it. Step 3: Remove the screw securing the PG sensor to the unit, and remove the sensor.

Reset Printer Epson T13. Dying To Win Robert Pape Pdf Printer. Step 4: Remove two CP (S-P1) (M3x6) screws securing the PG motor and remove the motor. Encoder Plate Encoder Plate Figure 3-53. PG Sensor and PG Motor Removal ASSEMBLING POINT • When you install the PG motor, make sure the backlash between the PG motor and PG motor transmission gear is between 0.05 and 0.15 mm (almost no backlash). • When you install the PG sensor unit, align the C-cut portion of the unit with the lower shaft securing the PG motor to the frame. ADJUSTMENT REQUIRED When you install the PG sensor or PG motor, perform the platen gap motor value (platen gap) adjustment, as described in Section 4.1.7.